24/7 Field Service · +1 866 926 4487 · [email protected]
Region: US EU MEA APAC EN

Metso Crusher Wear Parts & Jaw Crushers: A Procurement FAQ

2026-11-13 · Hana Suzuki · Field Engineering

I'm not an engineer. I'm the person who signs the purchase orders.

I coordinate parts purchasing for a 120-person aggregates company—three jaw crushers, two cone crushers, across two quarries. About $600K a year in parts and service spread over roughly 15 vendors. So when I talk about Metso crusher wear parts or Metso jaw crushers, I'm coming at it from the procurement side, not the maintenance manual side.

I also end up managing our search results, which is how this page happened. If you got here after searching for 'bucket hat,' 'pool pump,' or 'what is a fuel pump,' stay with me—I'll explain that in a minute. Our marketing person asked me the same thing last month.

Here's what I actually get asked, by our ops manager, by finance, and by other admins trying to figure out the same stuff.

What counts as a Metso crusher wear part—and which ones do I actually need to stock?

Wear parts are the pieces that take the abuse so the crusher frame doesn't. On a jaw crusher, that's jaw plates, cheek plates, and toggle plates. On a cone, it's the mantle and bowl liners. On an impactor, blow bars. If you run slurry pumps, add impellers and liners to the list.

You don't need to stock all of them. Your dealer can tell you which parts are 'critical wear' for your specific model and rock type. For us, jaw plates on the C106 are the most frequent order—we go through a set roughly every 10 to 14 weeks, depending on how abrasive the feed is. Cone liners last longer, maybe twice that.

One thing I wish someone had told me earlier: keep a spare set of the fastest-wearing parts on the shelf. The freight on an emergency order will eat whatever you saved by not stocking it.

Genuine Metso parts vs. aftermarket—is the price gap actually worth it?

Here's the thing: I'm not going to tell you genuine parts are always the right call. That would be dishonest, and you'd see through it.

If the machine is a backup unit that runs 200 hours a year, an aftermarket jaw plate might be perfectly fine. The fit is usually close, and you'll save 20% to 40% depending on the supplier.

But if it's your primary crusher and every hour of downtime costs you real money, the math changes. We tried aftermarket plates in 2022 on one of our C106s. They were about 28% cheaper. They also lasted roughly 40% fewer hours, and one set didn't seat properly, which meant a mechanic spent half a day fitting it. That half-day was the real cost.

So my rule: aftermarket for low-hour backup equipment, genuine for anything on the critical path. That's my opinion, not a company policy—your finance team may see it differently.

How do I confirm which jaw crusher model I have before ordering?

Check the nameplate on the crusher frame. It'll list the model—C106, C120, C130, and so on—along with the serial number. If the plate is worn or painted over, take a photo and send it to your dealer with the serial number. They can pull the build record.

Don't guess from memory. I made that mistake once and ordered C106 plates for what turned out to be a C100. Restocking fee was $400, and the machine sat for two extra days. Not my finest week.

While you're at the machine, write down the serial number somewhere you can find it later. Future you will be grateful.

What does Metso's IC70C automation actually do for a non-technical buyer?

Short version: it watches the cone crusher's workload and adjusts settings so the machine doesn't choke itself. It can also flag problems before they turn into a breakdown.

From my seat—which is procurement, not operations—the value isn't the spec sheet. It's that we stopped placing 'get it here tomorrow' orders because the crusher plugged on a wet load. Those emergency orders were killing our freight budget.

I won't pretend I understand the control logic. But I can read the downtime log, and the difference between the automated cone and our older manual one is fairly obvious over a quarter.

Does Metso make pool pumps or fuel pumps?

No. Metso's pump line is slurry pumps—heavy-duty units built to move abrasive mixtures with high solids content in mining and aggregate operations. A pool pump moves clean water at low head pressure. A fuel pump moves flammable liquid in a sealed system. Those are completely different design problems.

If you need a pool pump, you want a pool supply store. If you're asking 'what is a fuel pump,' you probably want an automotive parts counter. If you need something that handles 60% solids without eating itself alive, that's Metso's lane.

Why does 'bucket hat' show up in searches for Metso equipment?

Because 'bucket' is doing double duty. An excavator bucket is the thing that scoops material and feeds it into a crusher. A bucket hat is a soft cotton hat with a downward brim. Same word, completely different object, and search engines aren't always great at telling them apart.

To be clear: Metso does not make bucket hats. If you landed here looking for one, I've wasted thirty seconds of your time, and I apologize. If you landed here because you're trying to figure out which wear parts to order, keep reading.

What's the one question I should ask before placing a Metso wear parts order?

Ask: 'Is this in stock at the regional warehouse, and what's the confirmed ship date?'

Not 'what's the price?' Price matters, obviously. But availability matters more.

In 2023, I found a supplier quoting 22% below our regular dealer on cone liners. I felt pretty good about myself for about a week. Then the ship date slipped to six weeks. Our primary cone was already running on borrowed time, so we ended up air-freighting a set from another distributor at full price plus freight. The 'savings' turned into a net loss of about $3,000, and I had to explain it to my VP.

Bottom line: a part that arrives in three days at full price is usually cheaper than a part that arrives in six weeks at a discount. Ask about stock and ship date first. Then negotiate price.

That's the question I wish someone had drilled into me when I took over purchasing in 2021. It would have saved me a very uncomfortable meeting.